WM12Q390GB Front loading automatic washing machine Siemens IQ300 varioPerfect
Download Siemens washing machine WM12Q390GB user manual in PDF format: WM12Q390GB-EN
Performance
- Energy efficiency class: A+++
- Capacity: 8 kg
- Maximum spin speed: 1200 rpm
remaining moisture: 58 % - B spin class
- Energy consumption :179 kWh per year, based on 220 standard washing cycles
- Energy consumption:standard 60 °C cotton programme 0.82 kwh full load and 0.8 kwh partial load and 40 °C cotton programme 0.71 kwh partial load
- Cottons/coloreds 60+ecoPerfectCottons/coloureds ECO 60 and cottons/coloureds Eco 40 Cotton/color 40/60+ ecoPerfect are the standard washing programmes to which the information in the label relates. These programmes are suitable to clean normally soiled cotton laundry and are the most efficient programmes in terms of combined energy and water consumption.
- Programme time:60 °C cotton programme 196 min at full load 191 min at partial load and 40 °C cotton programme 186 min partial load
- Weighted power consumption off-mode / left-on mode: 0.1 W / 1.49 W
- Water consumption 8700 litres per year, based on 220 standard washing cycles
- Drum volume: 58 litres
- Noise level washing : 54dB (A) re 1pW: Noise level spinning:76dB (A) re 1 pW
Programmes/functions
- Fully electronic control dial for wash programmes, temperature and special progammmes
- Special programmes: rapid 15 minute quick wash , textile guard re-proofing programme, mixed fabric quick wash programme,delicates/silk programme
- Touch control buttons: start/reload, less ironing, extra rinse, ecoPerfect, speedPerfect, spin speed selection
Key features
- varioPerfect:speed or energy efficiency with perfect wash performance every time
- antiVibration Design – for more stability and quietness
Additional features
- Display for programme progress indication,time remaining and 24 hours time delay
- Aquatronic wash system
- Flow-through sensor for optimum water use
- waveDrum
- autoLoad
- Reload facility
- Detergent over dosage display
- End of cycle buzzer
- Foam detection system
- Electronic child safety package
- Multiple water protection
- Self cleaning detergent dispenser
- Metal door catch
Technical Information
- Dimensions (H X W X D): 84.8 x 59.8 x 55 cm
- Slide-under installation
- Large silver-white door with 165° opening and 32cm porthole opening
I am using Siemens vario 1q300 washing machine and it keeps restarting ..technician has visited but no error. cleaned the panel from inside and checked in detail. says its controller module has malfunctioned. can anyone help out?
The technician will have to replace the control panel, it’s an electronics fault.
Hi
I have a Siemens iq300 7kg front loader washing machine. How I set the machine to 15 min rapid wash. I have the 30 min wash cycle on the dial.
Thanks
what is sign lock 20minutes
I300 machine just completely stopped. No light on and door jammed. Any idea as to the reason. Had been perfectly ok then just jammed
The washing machine is on eco perfect mode by mistake..and does not start.
How do I disable this option and have the machine working again ?
Hi everybody
my washing Machin 1q 300 is stuck with an error of E-17 many times I cleaned it. every time i start the Machin there is the same massage in screen E-17. what can i do? and what is problem?
is there any body help me.
Hi! What does E06 mean? This appeared after I used the cotton eco option. I can’t open the door as well. Thank you.
Hey..I use siemens iq300 but it has no digital screen….when its washing often I just get a buzzer sound n gets paused….I have to give it a start again…could anyone help me to solve my issue?
My Siemens IQ300 is having a problem dispensing the fabric softener, the fabric softener compartment is always full at the end of the cycle (some additional water in it). I have tried clearing the water inlet hose and cleaning the soap dispenser tray. Any other ideas for me to check please?
Pull out the fabric softener compartment (all drawer out), at the end is probably piece of withered softener.
The machine finished the program ( 30 C ) blinking the key and the adding water together , cant open the door , what to do ?
my IQ300 doesn’t rinse properly..clothes are still very wet..I’ve checked pump outlet and clear inside opening..what next to do..??
My Siemens iq300 washing machine keeps increasing the time always. Is there any solution to this problem?
The washing machine iq300, sirm3ns cut of mid cycle, cannot oprn door or turn on or off. No power at all. Help please?
The washing machine cut of mid cycle, cannot oprn door or turn on or off. No power at all. Help please?
I have a seimens iq300 washing machine. Its gives Error Code 17 on every 8 Min. If i start 30 min cycle its take dubble time to finish cycle. how could i fix this issue , any simple trouble shooting method instead calling repair man
What does E 06 mean on Siemen Iraq 300 what is the answer
I have iq300 7 kg siemen washing. i am electrical breaker triping when its run more than 7 minutes
also washing machine became very hot . we change the knob to all the tabs still same same issue
can you pls advice the good suggesttion
Hi my Siemens iQ300 is beeping and displaying -0- with the lock button flashing although door still opens. How can I fix it?
I have a seimens iq300 washing machine, all numbers and alphabets is flashing and i am not able to start or running nothing , how could i fix this issue , any simple trouble shooting method instead calling repair man
What is e-21 iq300 varios perfect and how to reset
Anyone know why my machine won’t start – it’s displaying the door symbol but has clothes in the drum and the door is closed.
No error message but 10 00 keeps flashing up after the cycle time, and when I press the start button nothing happens!
Thanks
e 21?
Anyone know why my machine won’t start – it’s displaying the door symbol but has clothes in the drum and the door is closed.
No error message but 10 00 keeps flashing up after the cycle time, and when I press the start button nothing happens!
Thanks
What does an e29 error message mean and how do I fix it please? Thanks
What is a E 17 Error
Is someone available to answer my question at Siemens customer service? Please!
MY IQ500 DISPLAYS E18, I CANNOT OPEN THE DOOR. ANYWAY I CAN GET THE DOOR OPENED? I DID TRY TO RESET PULLING THE ELECTRICAL PLUG BUT STILL NOT WORKING. PLEASE KINDLY ADVISE HOW TO OPEN THE DOOR AT LEAST. THANKS.
Hi, siemens iq 500 error code e 36 what is mean? Thanks
What is F21 on Siemens E10-46 washing machine? I cant open the door or put any other program on.
E05 is displayed. What should i do?
Hi. I have an iQ300 washing Machine and every time it washes and the cycle is complete, inside the tray, the middle part, for the softner, is filled with water and softner. I have washed it a zillion times and no solution. Can someone help out! Thanks
hi. i have got a iq300. and e13 come on. what is it and how can i fix this . please help me.
how do you stop this machine from beeping???!!!!
PLEASE HELP
My IQ300 washing machine does not start. It gives beep sounds. But does not start.
Load isn’t finishing or rinsing out the water. A washing basket icon keeps flashing what does that mean?
What does P on the display mean?
My Siemens iq300 washing machine has stopped taking the fabric conditioner? Can anyone advise please
Our Siemens washing machine ( WM12Q391GB ) has stopped working, if you set a programme and press the start button it just beeps twice then nothing happens?
Our Siemens WM12Q391GB Washing machine wont start, when you set a program and then press the start button the button makes 2 rapid beeps then nothing happens?
Machine leaking water will not allow cycle to operate. Door image showing on display and beeping if try to start cycle. Pressed other buttons which then shows F17?
brand new iq300 stops in wash mode and do not drain. please help
The machine just went dead mid-cycle. No error message, no power light, the door is locked. There seems to be no problem with the electricity source.
What should I do? I have tried unplugging and replugging, but no change.
I cannot select, how can I do. I need help. Thanks
What does code E43 mean?
What is error code E43?
This is not in the manual?
What is f18
Cycle is completed but no emptying of water
I have an code F21 on the front of my Siemens washing machine and the door will not open what do I do?
Hi, fault F21 Siemens washing machine means failure of the engine, likely to be worn carbon brushes, it is necessary to call a repairman.
I have error code F21. Siemens washing machine E16 46. What does it mean? and what to do..
Hi, my Siemens washing machine is flashing F37 and beeping constantly
hi my machine stopped mid dryer cycle and is reading two errors on the screen ‘PUNP’ and ‘E 06’ please can you help!!
Hi
I have an IQ 300 washing machine which is squeaking on high speed spins. Just in case it might be relevant I replaced the door seal a month or so ago due to a cut in the rubber.
Any ideas on the squeaking?
Hi I have F43 error message, I’m aware that is a problem with the motor but how do I unlock the door to get washing out?
pls give reply as soon as possible. i lodged the complint, they told us , change the pannel . so tell me what to do.
WHAT IS THE ERROR E5 IN SIEMENS IQ 100 WASHING MACHIN
Hi, I have a Siemans IQ500 washer-drier. After two successful loads today I started a third and the machine just stopped. I turned it off and back on and reset programme. It starts for a couple of seconds and then just stops with the display showing normally. Checked outlet etc. There is no error code showing. Bit stumped – anyone any ideas please. Thank you
Hi, hoping you can identify what problem I have on my Siemens washing machine …washing machine refuses to wash & is flashing F37 ,thanks
Siemens Iq700 Fabric Softener not being taken out. I tried to clean the compartment but no softener at all is coming out .
I recommend removing the entire magazine conditioner from the machine and clean it thoroughly. The drawer is pulled out and pushed down, then can be removed.
I have an iq300. Been trying to open the filter cap to do a drain and clean but the cap just keeps rotating and not opening… and solutions? Many thanks
A few minutes before the washing cycle ended on cottons 60 degrees, the machine shut off. No power and I had to manually open door lock on bottom. Checked the fuse and the plug, both are OK. Any ideas what to check next?
The wash cycle symbol is flashing even though the machine is on its last spin. Is this a fault.
Hi the way cycle symbol is flashing even though it’s on its last spin. Is this correct
can I rinse only with this machine
can I spin only with this machine
Hi, does anyone know what e:23 error means on iq:500 machine and how to fix it?
Hey
How to do rectify e17 error
I have a siemens vario perfect 1300.
I had it on a 40 wash and it has not finished cycle.
there was a symbol of what looked like a bath with a cloud above, or bubbles.
it wont empty or finish cycle.
tried to empty on button but no luck
can anyone help
What does E17 error means in washing machine iQ300
Hi, Fault E17 is a problem with water supply, inspect hoses and strainer.
IQ 500 by the way .
Can you please help my Siemens wash machine I select the setting and I want to start but it’s beeping 2 times and the lock comes on flashing it’s not starting at all please I need help asap thank you
My machine has started displaying error e16. If I switch machine off and rotate drum, it then starts. Is there anything I can do to stop the error message
Hi, error E16 means: Very high water level. The problem might be in the level sensor
When powering the machine we have an errror message ‘E00’ and nothing happen. How to fix this problem. Pls help. Thanks
What does f43 on display panel mean please?
Fault F43 – that is a motor error. This error code mostly means that the carbon brushes are end of life.
How do I turn off the bloody beep at the end of a cycle?? My iq300 doesn’t have the intensive stain button mentioned in previous answers so at a loss…..
what does it mean when two flashing dashes shown in LED display and am unable to get door to release. had machine (iq300) on 60 cycle, now won’t release, no error code just flashing dashes ( – – ) despite trying empty cycle and switching off at mains.
Is there a way to completely reset the machine? E.g. by pushing several buttons for a longer time?
What does error F19 mean on an iq300! Can anyone help?
Fault F19 indicates a problem with the heating circuit
Hi,
i have no errors but every time i try to start my iq300 machine it beeps twice and doesn’t start,
when i moved the it to have a look at the back connections the start\pause suddenly blinked again and i could start it.
the same issue reoccurs all the time – any idea what could be wrong?
Hi, it is strange that the error message is displayed. Try to lock the door, push and then give the start, it might help…?
Siemens washing machine IQ100 code E-16? Machine doesn’t start.
Hi, Fault E16: Very high water level – Error. Probably a problem with a switch of water
i want to know that can we put starch or bleach in my siemence Iq300 front door washing machine plz do reply me
E:17 is written while my washing what to do my machine model is iq300
Please I have an iq300 washing machine which gives error f43, I changed the carbon brushes well, it did not work and still showed f43, I replaced with the same working motor and it gives error f43, please what I do or what do you think the problem will be?,
My washing machine always gets a beep sound it will struck in any one program .start button won’t work what is the problem plz reply?
bonjour, Ma machine siemens iQ 300 C’est bloquée à 44 minutes pendant le programme maintenant impossible d’ouvrir le Hublot et quand je tourne le bouton sur un des programmes un code erreur F26 s’affiche .. est ce que quelqu’un pourrait me dire de quoi il s’agit, et si ça nécessite de contacter un professionnel pour la réparer ??
Merci par avance,
Cordialement,
What does e34 mean on a Siemens 12Q390 washing machine
What does e34
Any programme to wash dirty collars and also which programme for ”less-ironing” !
How do I stop the end of cycle beeping? It’s so annoying!
Hello,
My wife tried washing the blanket in the machine (do not know why), the cycle started with water but it did not rotate. I guess it is an overload. But could any one help me diagnose this ? As now if I try to run it empty the cycle starts but the drum does not rotate. Also there are no errors on the screen.
I have a Siemens iQ500 washing machine bought in May 2015. In the past two weeks it has suddenly started to have problems with rinsing. Especially when draining the water for the first time after washing cycle. It seems there is too much water when it starts the first spinning while draining the first time after washing. The drum is just “hitting” the water and the machine does not get the water out, resulting in foaming. I have not used excessive amounts of detergent – actually I once washed with only water and same happened (no foam of course in this case). Water comes out well when just filling the machine with water and then draining. But when spinning & draining there is this problem. I have opened some hoses my self and checked that there is nothing in the hoses blocking the water. Maybe it is not getting the drum in balance well enough – broken shock absorbers or broken sensing of unbalance??? Any hints before I call for the service (I still have the guarantee)?
Hi..does washing come out cold when cycle finished,mines coming out colder than before..thanks
I cannot open the dooor of the machine after a cycle – it displays an error message of E:61. Any idea what this means please?
Fault E61 mean: Door unlock switch failure. May help to disconnect from the electricity
I am not convinced my washing machine is heating the water. I have put in on a few 90 washes and opened during the cycle at at the end and the drum is cold. There is no code showing. How or what do I do please and thanks
Maybe you set low temperature wash, if not, the fault is in the heating element.
My siemens varioperfect iq100 shows E:00. I have disconnected for a longer period. What else can be done?
This forum is awesome. I’ve spent the last two days worrying about my machine being broken and all I had to do was to push a button and it started working again!
Hugs,
Raf
What does f18 mean
What does F18 mean?
F57 and we can’t get the door open!! Tried all methods suggested including fishing line!! Checked the motherboard – no burn outs! Motor looks as new despite the machine being 6 years old. Continuity and resistance check all ok? Living in Cyprus and can’t seem to locate a Siemans engineer. HELP !!! ?
Hi, Fault F57 is a communication error so between the electronics module and another part.
The only advice how to repair this defect itself is to unplug all the connectors clean and dry them.
how do you stop or over ride the intensive dry button ? my towel smells totally “cooked” after 1 hour and i want to take it out before the programme of 2 hrs 39 mins is finished. i have pressed various buttons and now it has reset to start all over again – my towel will be burnt to a cinder not to mention the waste and cost of electricity. i have tried turning it off at the mains and waiting 3 minutes but this did not work. I don’t think it is a child lock problem – (no CL message) and i do not appear to have a temp button although i do have an option button but this just runs through the spin cycle speeds. please help asap. i have lost the instruction manual.
The fabric softener is not going into my wash, this section of the drawer remains full after every wash………… Why why why?????????????/
F18 Siemens but can’t open the drain door to clean out pump-only twists 80* anti-clockwise. Stuck. Any help really appreciated. Thanks
Take one wrench, one strong person (husband in my case) and a fair amount of brute force= open door! Lots of twisted hair emerged. Thanks, Wendy
How do to eliminate the intermittent sound every time at the end of wash?
You can change the volume of the buzzer according to your requirement.
The operation procedure:
A. Switch on the machine,turn the program selector to Off .
B. Turn the program selector to cold Easy-care, press the additional function button Intensive stains and don t loose, you can hear the volume of the buzzer from minimum to maximum to off cycled. If you decide the volume that you wanted, loose your finger.
C. Finally,turn the program selector to Off . If necessary,select other programs by turning
the program selector after several seconds.
D. If the volume of buzzer has been opened,you can hear the audible feedback as same volume as buzzer when you press Start button. If be not opened,you can t hear the voice.The operation may check if the volume of buzzer has been opened.
The IQ300 doesn’t have a function button called ‘Intensive stains’. I have tried all the other function buttons, none work.
If anyone has a version that works for the IQ300, please post, would be deeply appreciative.
Snap to the comment about the IQ300 beeping issue. One of the few things I stipulated when we bought the machine was that it musn’t make a beeping sound at the end of the cycle – grrrr.
Siemens Iq300 will not drain and shows F18 Fault.
Cleared the filter which was clogged and would not turn.
Tried the rotate backwards and fwds to loosen etc but no joy so had to remove pipework etc..
This was done by taking off the top black hose (one with circlip) from under the drum and reaching into remove hair grips which then allowed the filter dial to turn. The pump was cleaned out and for a double check I undertook a full removal of the discharge hose (mainly because of the smell as I thought I had cured the issue with the hair grips etc) which was cleaned by putting a hose pipe through it in the garden with water going through it to clean the pipe. Nothing found as a blockage on outboard side of pump. Put back together and went toghether very well with easy to remove clips etc and locating lugs etc. Then when re-installed Put a bucket of water into the drum and closed the door. Could see this was above the drum bottom level. Turned the washing machine to empty cycle and start – Pump started but level did not go down. Drained off again via black pipe bleed pipe and the when emptied via this method I started the cycle again with the filter out (no water inside) and could see the fan rotating in the cycle and tried to hold this back with a rag and still had lots of torque etc indicating the motor is OK.
Totally lost now – Siemens helpline advises reset the system with start pb depressed for 3 seconds which is OK but the machine is doing what it should in terms of starting the pump for a cycle and then going to zero on the dial. The issue is water is not going out of the exit pipework and I cannot understand why.. if there was a sensor problem etc I would expect the pump not start or not to stop etc but the cycle performs its operation and the stops.F18 is not alarm that comes up when on empty cycle it only does it on the normal cycles ie If we put a load in washes and spins but then goes out in F18.
any ideas as I don’t want to shell out £90 for an engineer to do 2 mins work and all main devices seem to work.
I have the same problem. Found some sand in the pump. cleared it but it still does not work. Noticed that there is water leaking inside the pump. Is this normal or should I seal it?
I have an F15 flashing! Please advise…..
Probably water overflowed.
Disconnect from electricity Remove the cover from the bottom and dried
What is mean of E16
Fault E16: Very high water level – Error. Probably a problem with a switch of water
Hey! Have a problem with our washing machine Siemens iq300 wash&dry. Every time we want to wash our clothes in takes about 4-5 hours. On the screen it says 00:01h left (so 1 min) and it starts showing it when ideally there should be 1min left before it finishes. However this 1 minute lasts for additional 3-4 hours. What should we do?
Hi, this is a common fault with Siemens washing machines, unfortunately I can not cope? Anyone have experience with repairing?
I have a problem with my iq300 i feel always the water for washing and flashing are not enough, always the clothes still stain with the poweder soap after finish and even its visible.how can i solve that issue? Note its like that since new
I understand correctly, that the machine is not enough water?
my siemens IQ100 manual stopped while running in between, no lights flashing total off, pls suggest still water is inside machine
How can I SPIN, just for a short time (minute ?)
my siemens E 10-46 is showing f 16 fault, what i have to do? its showing key symbol blincking. ply reply at earliest
Hi, Error F16 indicates the washing machine door open. Try to push the door and start the program again.
What dose f43 mean
F43 – that is a motor error. This error code mostly means that the carbon brushes are end of life. You can replace them yourselves with new spare parts.
I found on Youtube nice instructions for repair: https://www.youtube.com/watch?v=83D5Uw_jKxY
Hai f36 anyone’s? Please?
my machine shows E:00 . What is the fault in it
E00 is a generic error, help sometimes disconnected from power for 30 seconds
hi
i have a error 80? i started a 15m wash and somewhere when draining in the end… error e:80 was displayed
thx in advance
Hi,
E80 is a general code relating to the recirculation pump. Either the pump or wiring has failed, or the computer thinks it isn’t there.
Hi,
I get also the error E:80.
This happens at the end of any program when the draining is finished. The machine doesn’t unlock the door and the error is displayed. If I turn the main button to off and then go to any program, the error still appear. If I pull on the manual rescuing door unlocker, I can open the door and start any program (which will fail finally at the end)
I’ve completely removed the pump, emptied the filter, the incoming and outgoing water pipes.
I’m wondering if it’s the door locker or the main card that has to be replaced.
Thanks in advance for your help.
F18? Anyone? Please?
Hi, F18 Siemens fault code is problem with draining.
Siemens IQ300 tumble dryer will not work because the “Door” indicator light is permanently stuck on and won’t go off even when door is securely shut?
What does error EO6 Pump mean?
E06 = Drain error detected
Check drain pump filter
Check drain pump for blockage or restriction
Check outlet hose for blockage or obstruction
Check drain pump operation
Check drain pump wiring
Siemens IQ 300 Washing machine, the drum has started making a rough grinding noise when spinning during the wash cycle, it is especially noisy when doing the spin cycle ( sounds like its no longer running on bearings ) ? . When you spin the drum by hand it does not make the usual free wheeling ‘whirring’ noise but makes this heavy grinding noise, any clues as to what the fault may be ?
i also had that problem that machine starts scalding and grinding during spin or rinse cycle the representative of siemens came and fix that problem….and problem was that the coin was stuck in the bottom of drum so he removed it…its now working perfect may b its the same reason of your machine…u just have to be very careful that no pins coins and any kind of metal thing in pockets…makesure u check.it before adding clothes….
I Have a problem with the alarm at the end of a wash. I Would really like to disable it. Is it possible to permanently terminate this annoying feature?
I found advice how horrible beeping mute, I do not know if it will work, please about your experience.
http://www.justanswer.co.uk/appliance/8l2az-jlw-1400spin-washing-machine-showing-fault-e60.html
Can anybody help….. What does E60 mean??
Thank you
Faulty – Error code 60, is problem with mainboard communication, the problem may be a bad connector terminal. I recommend to disconnect the connector and clean.
Hi,
I have a thumble dryer Siemens IQ 700 and appears the alarm “empty water tank” which stops the dryer, but there is no water or small qty of water in upper collecting tank.
I have opened, clean and test run – water level sensor and check water pump – looks everything ok.
Looks that dryer is working when I have it open but at first cycle when machine is closed (all covers in place) again appears the alarm.
Please give me some more ideas what I should check.
Many thanks!
Hi, I tried to fill the water tank descaler. Perhaps the sensor is blocked.
Siemens xlp 1600 error code F12? Please help!
Hi, Error – Fault F12: Water in the base pan. Appliance leaking.
hope you can help. I have a siemens IQ700 washing machine and error code f67 came up. I have drained and cleared a coin from the pump but the error code remains and I can’t get it reset-so machine won’t start-it only beeps and flashes the same error code. Have tried turning on and off at mains and didn’t work. Thanks for helping.
Error F 67 is a nonspecific glitch electronics appliance. Disconnect the machine per hour from electricity. If, after reconnecting the error persists, call customer service.
what is the meaning of E3 in siemens WM08G260IN?how can it be removed?plz do reply….
Fault E3 is an engine failure. Electronics are trying to spin the drum, but for some reason does not rotate. Can You spin the drum by hand? If yes, Call a technician.
Hi my machine display f18 . I have drained it and cleaned the drain pump. But it still comes up and won’t spin. Advice please .
Thanks
Now we have a professional intervention. Does the pump power supply ok? If so, it must be replaced.
Washing with the “wool” option doesn’t work for me. It starts, then stops after a few minutes, and the timer just goes down slowly. How do I fix this?
siemens washing machine -every thing is ok., only d start/load button not operating., what could be the problem? no beep sound too.
What is error E5 in Siemens WM08G260IN?
Awaiting your kind reply.
Hi, Fault E5 detected in motor or drive circuit.
This error code can be generated by no tacho reading from the motor (the electronics cannot see the tach generator of the motor), a triac fault or short circuit or a faulty reversing relay on the control board. The washing machine will try to start the motor but after several attempts the program will be aborted with this error code which is again consider to be a “fatal error”
what does f:48 on the Siemens iq 300 washing machine mean
Error 48 is a problem with the door lock, if the water does not flow out, it will be just faulty sensor
what does e17 and e4 error indication means in Siemens washing machine mean model wm10k250in iq 300
E17 is a problem with water supply
E4 is a problem with water draining, check the filter
i got an F 18 error code
can’t open it
what does it mean?
Hi, F18 fault error code is problem with draining, tried to clean the filter?
status is reading CL can not put the wash on
Hi, CL mean Child Lock.
Press the TEMP and OPTION button together for 3 seconds
It appears lock symbol how to do
The machine does not display if the dial is sitting at “off” (top setting) so can look like there is no power.
To set the machine to just spin, turn the dial to “rinse/spin” and press the “extra rinse” button off, next to the “start” button. It explains this in a list of functions towards the back of the wee booklet manual.
Hi
The washing machine has a code flashing f 43 this was after a power cut and tripped everything off it hasn’t worked since . Could anyone help
Many thanks
Charlotte
F43 – that is a motor error. It may be that the motor can not run, might be enough to rotate the drum manually
My machine gave the same error . what is the solution ?
Unfortunately, correcting this fault requires a serviceman
This error code mostly means that the carbon brushes are end of life. You can replace them yourselves with new spare parts.
I found on Youtube nice instructions for repair: https://www.youtube.com/watch?v=83D5Uw_jKxY
what does e29 error sign indicate or mean?
E29 indicates a problem with the water supply. It often helps to unscrew the inlet hose and blow into Aquastop
How do i JUST spin to remove any excess water??
thanks
Hi There
The start button is not starting the washing programme as per normal, it is just beeping twice. Can you help?
Try to push and hold the door lock might be wrong.
Hi Louise,
did you find the reason of your beep twice issue? I have the same issue.
Regards
Prakhar
Hi! I cannot unlock the door! The Key still displayed! Help please! Thanks
Did you get the idea how to do open the door i have the same problem key fishing and door are closed
What does a symbol of key mean? How do I undo it to start the washer IQ 300 Siemens washing machine .
Just hold the buttom of start for 2 sec
I just got at new IQ300 delivered and after removing the shipping stabilizers, I plugged it in and nothing! No energy at all, no display, no nothing. Did I miss something or is this simply a defective machine?
Hi Joey, it looks like a faulty washing machine. I recommend claim.
what is an F29 error? It comes up as soon as I put cycle to start. I press the start button a second time and the warning stops.
Fault Siemens – F29: Not Detected water inlet on flow sensor.
It may not be a bad sensor, it might be enough to decalcify
last few weeks washing machine gets stuck on washing cycle with clock showing 1 min left remaining unless I press “speed perfect” at the start or only use the 15min rapid cycle. All other cycles it gets stuck even if I go out and come back a few hours later it is still on and stays washing with 1 min left on clock unless I switch it off and change to one of the above 2 cycles?
I have been using the machine since April 2013.
Did you find the problem ? I Have exactely the same behaviour ?
Hi Liu & Marc,
Any solution to this. i have encountered the same problem.
Hi all. Displayed an error code or the machine is waiting for the expiration of one minute?
Hi Marmen,
No error codes. the machine waits for the expiration of 1 minute.
but just works just fine in “super 15′ mode” (same as Liu experienced)
Guys Please help.
Hi all,
I can not trace a solution to this problem in the service manual.
Repairman recommends checking water level sensor.
Hi Marmen,
A repairman – checked the machine.
He says the machine doesn’t stop intake of water, this is a problem with the board (as the water pump works fine).
Your repairman guessed it right about the water level sensor.
Can this be replaced?
Cheers.
I have had this “1 minute” problem intermittently for several weeks / months and have used ‘speedPerfect’ setting to overcome issue. It’s being fixed under warranty and the service guy has been and indicated possible fault with Heating Element. Explanation: if Washing Machine fails to heat water then it gets to end of the wash cycle (with 1 minute to go) but is not allowed to finish because temperature does not satisfy selected wash programme. I’m not convinced as the thermostat is more likely to exhibit an intermittent problem than heating element. I will update when repair is completed hopefully next week. Best regards
Hi all. See previous comments …
Machine now functioning perfectly after visit from diligent Siemens / Bosch Service Technician. Intermittent fault due to fault in wire connector in Heating Element circuit. As previously comment – lack of heat caused ‘1 minute’ issue.
Best regards
How much charges to be paid
What does error F18 and F28 mean please?
F is not Error code.
E18 indicates a draining failure.
Can be clogged filter, or a fault on the pump.
E28 is Turbidity sensor fault
We would strongly advice seeking an engineer for this fault as well as it is often not easy to understand or diagnose issues with turbidity sensors.
How do you fix the e18 error code?
How do u fix e18 error code
How do I fix error code e18?
E18 means: Drainage hose blocked or kinked
“Clean filters in the water supply hose. Attention: The leaking water may be very hot (risk of scalding). Set programme selector to. Pull out the mains plug. Check whether the drainage hose has been installed without kinks. Loosen hose clip on the siphon, carefully remove drainage hose (residual water). Clean drainage hose and siphon spigot. Hold drainage hose in a bucket and select the programme. Connect drainage hose to the siphon and check for leaks.”
What is a f17 error
Error F17 is a problem with water supply
What to do about a f17?
Usually can purge inlet strainer water. Sometimes just unplugging and replugging the AquaStop
How do you do that? (Unplug the aqua stop and purge the inlet strainer…)
AquaStop is a box on the water supply hose. Before it is strainer, clean it.
What does f18 mean?
what does cl mean on display panel?
Hi, CL faulty mean Child Lock.
Press the TEMP and OPTION button together for 3 seconds and it will go off
Thank you! Thought I had just broken my mum’s washing machine, on mine I pushed the start/reload button and it cleared the CL….phew!
Thank You! Just cleared my too. Have no idea how it came on!!!
Im having the same problem, can’t get the child lock off but have no option button? Please help asap
Press and hold the start button for a few seconds.
Thank you, that helped!
thankyou had the same problem
Thank you. You solved my problem!
Thank’s to you i can Wash my laundry again, i was beginning to worry if the Washing machine is broken. I’ve pressed the start button for a while and that fixed my problem. Thank you! :))
Thank you: that worked a treat.
Hi,
When completing wash cycle machine not go into full spin as clothes are still very wet when removed…
Is it that I’m using wrong settings..?
Siemens Various iq 300 machine
What is a e25 error
It’s a problem with the pump or drain hose.
what does e13 mean?
Washing machine Siemens fault
E13 indicates problem with the door lock. It may be even a faulty sensor is closed.
thanks, I’ll check it out.
how do you fix this problem ie error e 13 on a seimens 1q300
Sir, I have Siemens IQ300 model but my machine error come e21 machine not working not open what is problem
Hi, The manufacturer does not report the error E21, but I found the answer here: https://www.justanswer.co.uk/appliance/dou3d-e-21-error-code-bosch-washing-machine-door.html
error E21 can indicate a fault with the motor or the main control board. Try erasing the stored codes first, in case it’s a spurious fault, as follows:
1. Turn the knob to off.
2. Turn the knob to the 6 o’clock position.
3. Wait 2 seconds.
4. The start/pause should begin flashing.
5. Press and hold the spin button.
6. Turn the knob to 7 o’clock position.
7. Wait 2 seconds.
8. Release the button.
9. Turn the knob to off.
This should erase the error code and get the machine running again. You might need to try it more than once to achieve a reset. If the start button doesn’t flash, just carry on trying to erase the codes.
What is e18 error
The e18 message came on and a warning button sounded. What happened and how do I correct it?
Hi, fault E18 means: Drainage hose blocked or kinked
Solution:. Pull out the mains plug. Check whether the drainage hose has been installed without kinks. Loosen hose clip on the siphon, carefully remove drainage hose (residual water). Clean drainage hose and siphon spigot. Hold drainage hose in a bucket and select the programme. Connect drainage hose to the siphon and check for leaks.
Clean filters in the water supply hose. Attention: The leaking water may be very hot (risk of scalding). Set programme selector to
What is E:63 error
dear
iq300 8 kg rpm1200, how to operate 15 minites quick wash ,please help